Deck Stain Calculator
Two decks the same size can take twice the stain — it depends on how rough the boards are and how many coats you plan.
384 sq ft of coating at 250 sq ft per gallon
Where those coverage rates come from
Stain data sheets quote two rates for the same product. Cabot's semi-transparent deck stain lists 450–650 sq ft per gallon on smooth surfaces and 200–300 on rough. The calculator uses the low end of each range, because running out halfway across a deck is worse than one spare gallon.
That range is why the same 16×12 deck can take one gallon or three: a new, smooth board is half the surface of a rough-sawn one, and a second coat doubles the gallons again without doubling the area.
Gallons per coat, by area
| Deck size | Rough, 1 coat | Rough, 2 coats | Smooth, 2 coats |
|---|---|---|---|
| 10×10 (100 sq ft) | 1 gal | 1 gal | 1 gal |
| 12×16 (192 sq ft) | 1 gal | 2 gal | 1 gal |
| 16×20 (320 sq ft) | 2 gal | 3 gal | 2 gal |
| 20×24 (480 sq ft) | 2 gal | 4 gal | 3 gal |
What the gallons do not cover
Rails, balusters, steps and the fascia all take stain and none of them are in the board area. Measure rail length in linear feet and allow about 2 sq ft per foot for top and bottom rails with balusters; a staircase adds more because the treads and risers are both surfaces. Round up a gallon when you have rails.
Working it out yourself
Three numbers: the area, the coats and the coverage rate on the can.
1. Area. 16 × 12 = 192 sq ft of board. That is the top surface only — the sides and the gaps are not in it.
2. Coats. Two coats means two passes over the same 192 sq ft, so 384 sq ft of coating.
3. Gallons. 384 ÷ 250 = 1.54, so 2 gallons. At $45 a gallon that is $90.
The one-line version: gallons = area × coats ÷ coverage. Round up at the end, not in the middle.
Rails, steps and fascia are extra. Measure rail length in linear feet and allow about 2 sq ft per foot for a top rail, bottom rail and balusters; a stair tread and riser together are about 2 sq ft per foot of width.
What changes the number
Rough versus smooth. The same deck can take two or three times the stain. Weathered boards drink it; new smooth boards take half as much.
Opacity. A clear sealer is one coat. A semi-transparent is one or two. A solid color is two and hides the grain — that is the trade.
Spraying. A sprayer puts down more material than a brush and loses some to overspray. Budget 10–20% more gallons, plus masking time.
Weather. Stain wants 50–90°F and two dry days after. Direct sun makes it flash before it soaks in, so follow the shade around the deck.
Prep. Washing, sanding and brightening are most of the labor. If the old coating is peeling, stripping is a different job and a different price.
Three finishes, one choice
| Finish | Coats | Recoat | Note |
|---|---|---|---|
| Clear sealer | 1 | 1–2 yr | wet look, no color, needs yearly upkeep |
| Semi-transparent | 1–2 | 2–3 yr | grain shows, some UV block |
| Solid color | 2 | 4–6 yr | hides grain, peels instead of fading |
Oil versus water is a separate choice: oil soaks in and patches easily but dries slower; water-based dries in hours and cleans up with soap. Either base can be any of the three finishes.
What it costs, installed
Stain is $30–$60 a gallon; two gallons for this deck is $90 and a Saturday. A pro wash-and-stain runs $2–$6 a sq ft in 2026, so 192 sq ft is roughly $400–$1,150, with the average job in the $550–$1,250 range.
A simple restain of a maintained deck is cheaper — $0.50–$1.50 a sq ft — because there is no stripping. A full refinish with chemical strip and sand is $4–$8 a sq ft, or $770–$1,540 here.
The deck decides the schedule: horizontal boards take sun and water, so recoat every two to three years. Vertical rails last twice as long.
Frequently asked
How many gallons of stain for a 16x12 deck?
That is 192 sq ft. On rough or weathered boards at 250 sq ft per gallon, two coats is 384 sq ft — two gallons, with the second gallon half used.
Why does rough wood use twice the stain?
Rough-sawn boards have about twice the surface. The data sheets quote 450–650 sq ft per gallon on smooth surfaces and only 200–300 on rough, so the same deck can take two or three times the stain.
How long before I can stain new wood?
Three to six months for pressure-treated, until it stops taking water. Mill-glazed or pre-stained boards are the exception — ask the supplier which product goes over the factory finish.
Do I need to wash the deck first?
Yes. A cleaner and a brightener, then two dry days. Staining over mildew seals it in and the stain fails in a season.
Related
- Deck Calculator — boards and joists for the deck itself
- Fence Calculator — the same boards, vertical
- Paint Calculator — interior walls instead of exterior boards