Material Math

Paver Calculator

Pavers plus the joints is the real footprint. Then there is the base and the sand — which is usually the bigger part of the load you have to carry.

946 pavers

200 sq ft + 10% ÷ 0.233 sq ft each

200 sq ft4×8 in pavers, 0.125 in joints
3.2 cu yd4 in compacted, 2.5 yd³ loose
0.6 cu yd1 in bedding sand, not priced
$644pavers + base, sand excluded

    Why the joint is part of the paver

    A 4×8 paver covers 0.222 sq ft of material. With a 1/8 in joint it claims 0.233 sq ft of the patio — every paver effectively carries half a joint on each side. That is 4.3 pieces per square foot instead of 4.5, which on 200 sq ft is a difference of about 40 pavers.

    Small pavers make the joint matter less. A 12×12 in paver gains 0.5 sq in from a 1/8 in joint, about 0.35%; a 4×8 gains almost 5%. Same joint, different arithmetic.

    Pavers per square foot

    Nominal sizeWith a 1/8 in jointTypical use
    4×8 in4.3 per sq ftBrick patios, paths, herringbone
    6×6 in3.9 per sq ftSimple squares, quick layouts
    6×9 in2.5 per sq ftPlank look, running bond
    12×12 in1.0 per sq ftLarge-format, fewer joints to fill

    How deep should the base be

    UseCompacted baseNotes
    Garden path4 inFirm, undisturbed soil underneath
    Patio, firm soil4 inGeotextile helps in wet climates
    Patio, clay6 inClay holds water; the base has to shed it
    Driveway6–8 inGeotextile, and compact in 2 in lifts

    Working it out yourself

    1. Area. 20 × 10 = 200 sq ft.

    2. Waste. 10% for cuts and edges: 220 sq ft of pavers.

    3. Count. A 4×8 with a 1/8 in joint covers 0.233 sq ft, so 220 ÷ 0.233 = 944. Buy 946.

    4. Base and sand. 200 × (4 ÷ 12) = 66.7 cu ft loose, or 2.5 cu yd. Compaction adds about 30%, so order 3.2 cu yd. Bedding sand at 1 in is 200 ÷ 12 = 16.7 cu ft, 0.6 cu yd.

    Cost at the defaults: 200 sq ft of pavers at $2.50 is $500, base 3.2 × $45 is $144, total $644 before sand and edge restraint.

    What changes the number

    Joint width. A 1/8 in joint adds almost 5% to a 4×8 paver's footprint but only 0.35% to a 12×12. Wide gravel joints on small pavers change the count most.

    Pattern. A straight lay wastes 5%, a running bond 10%, herringbone with borders 15%. The pattern also decides how many cuts you make.

    Soil and base. Clay needs 6 in; a driveway 6–8 in with geotextile. The base is what fails first, and it is invisible when you are done.

    Edge restraint. Every patio needs it, or the outside row walks. It is priced by the perimeter, not the area.

    Sand. One inch of bedding sand plus polymeric joint sand. Skipping the joint sand is how the weeds start.

    What it costs, installed

    Paver patios run $15–$45 a sq ft installed in 2026, with $22–$28 typical; 200 sq ft lands around $3,000–$4,000 at $15–$20. The pavers are $2–$8 a sq ft, base and sand $2–$4, and labor $6–$14.

    DIY saves the labor but not the compaction. A plate compactor rents for $70–$100 a day and has to cross the base in two directions, then go over the finished pavers. That is the step that separates a patio from a pile.

    Extras that show up on quotes: sealing after installation ($1–$2 a sq ft), drainage corrections, and cutting around steps. Ask for those as separate lines so you can compare bids.

    Frequently asked

    How many pavers for a 20×10 patio?

    200 sq ft with 10% waste is 220 sq ft of pavers. At 4×8 in with 1/8 in joints each paver covers 0.233 sq ft, so about 946 pavers.

    How much base do I need?

    200 sq ft at 4 in is 66.7 cubic feet loose, about 2.5 cubic yards — but crushed base compacts by roughly 30%, so order 3.2 cubic yards.

    Do joints change the count?

    Yes. A 1/8 in joint adds almost 5% to each paver's footprint on a 4×8, which is about 5% fewer pieces. Wide joints on small pavers change it more.

    How deep should the base be?

    4 in compacted for paths and patios on firm soil, 6 in for patios on clay, 6 to 8 in for driveways with a geotextile underneath.

    Do I need sand and a plate compactor?

    Yes — 1 in of bedding sand, screeded, plus a plate compactor for the base and again over the finished pavers. Skipping compaction is what makes pavers rut.

    Related