Stud Calculator
Studs do not come out at "one per foot". Spacing sets the field, corners add two each, and waste decides what you actually buy.
31 field + 8 corner studs, 10% waste
Why the count is not just length ÷ 16
A 40 ft wall is 480 inches. At 16 in on center that is 30 spaces — but a wall with 30 spaces has 31 studs, because both ends need one. Then every corner takes three studs where two walls meet, so a rectangular room adds two extra per corner. Four corners is eight studs that never show up in the spacing math.
Only after that do you add waste. Ten percent is the figure that holds up across a normal room; a wall with four windows is closer to fifteen, because every opening costs a full stud length that gets cut away.
Studs per wall, at 16 in on center
| Wall length | Spaces | Field studs | With 4 corners |
|---|---|---|---|
| 8 ft | 6 | 7 | 15 |
| 12 ft | 9 | 10 | 18 |
| 20 ft | 15 | 16 | 24 |
| 40 ft | 30 | 31 | 39 |
| 60 ft | 45 | 46 | 54 |
Stud lengths for each wall height
| Finished wall | Stud to buy | Why |
|---|---|---|
| 8 ft | 92 5/8 in precut | Fits three 1.5 in plates plus the sill and ceiling allowance |
| 9 ft | 104 5/8 in precut | Sold as a 9 ft stud, not a cut-down 10 ft |
| 10 ft | 116 5/8 in precut | Special order in many yards — check before you plan on it |
| Any height, own plates | Cut from 16 ft stock | Cheaper only if you already have the stock and the saw time |
Working it out for a whole room
A 20 × 20 ft room is 80 linear feet of wall, and the count is four walls plus corners.
Each wall. 20 ft is 240 in; at 16 in on center that is 15 spaces, so 16 field studs.
Corners. Four walls × 16 = 64 field studs, plus 2 per corner = 8, so 72.
Waste. 10% takes it to 79.2 — buy 80.
Plates. Three per wall is 240 lf; ÷ 16 ft is 15 boards, and 10% waste makes 17.
At $3.85 a stud and $8.50 a plate that is $308 + $145 = $453. The same room at 24 in on center: 10 spaces per wall, 44 field + 8 corners = 52, 58 with waste — about a quarter fewer studs, but only if the wall carries nothing.
What changes the number
Spacing. 24 in saves roughly a third of the studs and is fine for a shed or a non-bearing partition. It is not fine for a wall with drywall both sides, or anything over 9 ft.
Corners. Every corner is three studs where two would fit the spacing. An L-shaped room has two outside corners and one inside corner, and the inside one adds two more.
Openings. A door needs two king studs, two jack studs and a header; a window adds cripples above and below. Budget one extra stud length per opening, plus the header.
Height. 9 ft walls use 104 5/8 in studs and 10 ft uses 116 5/8 in — both cost more per stud and are not always stocked.
Waste. 5% for a straight wall with no openings, 10% for a normal room, 15% where there are four windows. The cutoffs are the waste, not the count.
What it costs
A 92 5/8 in 2×4 stud is $3.50–$5.50 in 2026 depending on grade and yard; 2×6 runs $6–$9. A 16 ft plate board is $8–$12, and that is the line people underestimate — a 40 ft wall takes nine of them.
The 20 × 20 room above is about $450 in studs and plates at the defaults. Add $60–$120 for nails, construction adhesive and a couple of tubes of sealant, and $50–$150 for the permit if the wall is structural.
Labor is usually quoted by the square foot of wall, and on a small job it is the bigger half. If you are paying someone, ask for the stud count and the plate count as separate lines so you can see what the price is built on.
Where the extra studs go
| Feature | Extra studs | Note |
|---|---|---|
| Outside corner | 2 | Three-stud corner, one from each wall plus a filler |
| Inside corner | 2 | Same idea, on the inside of an L |
| Door opening | 2–4 | King and jack each side, plus cripples above the header |
| Window opening | 2–6 | Depends on width; cripples above and below |
| Partition tee | 2 | Where an interior wall meets a run |
The calculator counts field studs and corners. Openings, headers, blocking and bracing are the four things it does not know about, and they are where a framing list usually runs short.
Frequently asked
How many studs in a 40 ft wall?
At 16 in on center, 40 ft is 480 in — 30 spaces, so 31 studs along the field, plus two extra studs at each of four corners: 39 before waste. With 10% waste, buy 43.
How many plates per wall?
Three: one bottom plate and a double top plate. A 40 ft wall is 120 lf of plate, which with 10% waste is nine 16 ft boards.
Should studs be 16 or 24 in on center?
16 in for bearing walls, for anything carrying drywall on both sides, and for walls over 9 ft. 24 in saves money on sheds and interior partitions that hold nothing.
What length stud do I buy?
An 8 ft wall with three plates uses 92 5/8 in precut studs. A 9 ft wall uses 104 5/8 in. Do not buy 8 ft studs and cut them — you lose the plate thickness.
Does this include headers and openings?
No. Headers, cripple studs above doors and windows, and doubled king studs are extra. Add one stud length per opening plus the header material.
Related
- Drywall Calculator — the sheets that hang on these studs
- Deck Calculator — ledgers, joists and boards
- Concrete Calculator — footings for the posts